Well, we've already planned the laundry room makeover. We've actually demolished what was in there that I didn't like, and now we've built the wainscoting, and now moving on to the built-in for the washer and dryer.
Getting the Plywood
I went to Home Depot and I bought two of the 8x4 3/4 in plywood sheets. I had them cut them to long lengths of 32 in on both of them, which the remainder of that is 16 in. So I came home with about, you know, four different pieces of lumber. I also bought additional 1x4s, 1x2s and 1x6s to complete this project.
Step 1: Set the Side Panel
The first step is to actually put the panel up. It's 32 inches wide, eight foot. I set the panel first to kind of give me my height that I need to come across.
Now what I've done in the past is I've built cabinets that required pocket screws. The problem with this area is the cabinet's so big I can't pre-assemble it and then put it in place, which is what I would prefer to do. So I pretty much have to build this cabinet in place, and I'm just relying on that DeWalt 18 gauge nailer. I'm using 1 1/2 in nails and I think 2 in nails, depending on what I'm nailing into. You can see I've set the original panel, made sure it's level straight up and to the sides.
Step 2: Frame and Set the Top Panel
And then I'm simply using 1x2s to frame out the top of it so I can put the top panel on. Top panel is also 32 in. I'm just over 4 ft, I think I'm about 4 ft 6 in in length, which kind of sucks because it really weighs a lot, an 8x4 sheet of plywood. But it is where it is and I had no other options available. I thought this out long and hard.
So once I put the 1x2s into the studs, I simply put the plywood on top of the 1x2s and I just nailed to the 1x2s. Gives you a real nice firm foundation.
I like the way it's coming together. And when I sit back at this thing, once I get it all nailed, I think at first it's pretty big, but the room is big too. The room's I think 12 by 10, so it's good size. I'm not used to seeing such a large cabinet right above the washer and dryer, but as the project goes on you'll see it kind of fits the room really well.
Step 3: Level the Top and Measure Down From It
This is me just leveling that top board. I just wanted to make sure that I was coming straight across, because all my measurements for my next additional shelves below the top roof of this thing are going to come off the top of that instead of the floor, because the floor is more likely out of level. So I know my top panel is level, so if I measure down for my next two series of shelves, I know I'll always be right, at least level, so it'll look cosmetically good.
Step 4: Frame, Cut and Install the Two Shelves
Out in the garage I had to cut a few more of these 1x2s so I could start building the shelf. So it'll be two shelves: one right above the washer and dryer, and then another shelf splitting the difference between the roof of the built-in and the bottom of the top of the washer and dryer. So two different shelves inside.
One thing you'll see me do on this project too is I'll not build these shelves as deep as what I could go, for a lot of different reasons. One is I'm worried about heat from the washer and dryer and not having the ability to escape, or maybe the appliances getting too hot within, so I wanted to leave a void behind so the heat could rise. And another thing is too, you can't reach back 32 inches on a shelf. It's a lot of wasted space. So the shelves are gonna be open-faced, so there won't be doors on them.
So I thought the best thing possible would be just use the other 16 inch wide pieces that I got from the 8x4 sheets of plywood and use those as a shelf. And then what I'll do is I'll go buy a cheaper piece of 1/4 in plywood to back two shelves. It gives me more of a shallow shelf, but that's kind of what I'm looking for in this project.
Here I am cutting those shelves I just spoke of. You've seen me frame the two shelves in, so it's just a matter of getting the length for the 16 inch pieces that I had Home Depot already cut. Now Home Depot is a great place to go if you need panels cut, because they have a nice saw, pretty accurate. I could do it at home, but it's just so much easier when they're done there. I take advantage of it and it's free.
You can see there I simply just dry fit everything before I decide to glue and nail everything. When I go plywood to plywood, or wood to wood, I use wood glue. If I go like wood to drywall, I always use Liquid Nails. Wood glue doesn't work well on drywall.
So I've got both shelves, so I'm actually installing both shelves right now. I've got glue underneath each one. I pin it with three or four nails just to hold it tight for a little while. Also, by putting the shelves into the exact measurements I needed, it actually trues up the built-in too. So it's very important to make sure these shelves fit nice and tight between the wall and the panel.
Saving Money on the Drywall Side
Now you notice I didn't put a panel on the drywall side. I'm trying to save money there. 4x8 sheets of plywood, 3/4 in, are about fifty to sixty dollars, seventy dollars a crack. So when I get done painting you'll never know the difference. But it's a good way to save money, especially if you're going to build a built-in in place instead of a cabinet like you would in a garage and then bring it in after the fact. So I'm saving a little money there. Trying to do this makeover as cheap as possible and make it look as nice as possible too.
Step 5: Rip the 1x4 Trim and Glue On the Side Rails
Here's some 1x4s, I think I got them from Lowe's actually. I've ripped those down to be the same width as what the shelf trim boards are in the side of the built-in cabinets. I kind of want them all to match the same widths, so I think it's 2 1/2 in is what I did there. Makes it look beefy, but not too beefy.
So you see I got the initial part of the cabinet up, it's looking pretty good. So now what I'm doing is I'm gluing on the side railing trim pieces. I have a little block there, you see, in my right hand. I'm actually putting a little bit of an offset and having that board hang over a little bit. It looks good. You see that on your cabinets at home too. Gives you a nice little pocket there to put a bead of caulk, so when you paint it looks really good. Makes it look a little bit more decorative too. So I'm just overhanging just a tad. It's an eighth. Basically that trim board sticking out a little bit more than what the panel is. When you go flush it's just too hard to make that look clean.
Step 6: Backing Boards on the Drywall Side
Now on the opposite side I'm dealing with a drywall wall, not like this other first side that I did with the panel, so I had to put some backing boards in there to give me something to nail to. Just simply got some scrap 1x2s, put a little Liquid Nails on them, and nails, and that's the end of it. I think I hit a stud there too, so it's kind of nice.
Step 7: Left Side Trim, Level Across
So now that I got the backing pieces in, I'm going to go ahead and put the trim board on the left side. It's important to make sure I come level across, that way my header that I'm getting ready to put up last is level and straight. If it wasn't level, you'd probably know the difference, or somebody would. I know I would. A lot of people that do the same things that I do would notice it too. So I just made sure that we're level from left to right, kind of marked that spot. I think it was pretty good just sitting on the floor. So you see I just put a little wood glue on there, made sure my rail was straight, tapped it with a couple nails, and that's about the end of it.
Step 8: Shelf Face Trim
The final piece I'm going to put on this trim board is the header, actually put the header on last, but here I am putting the middle pieces in. Like I said, this is just really for decorative. I mean, one, the shelf I have in there, it's an unfinished edge, so it doesn't look good. So by putting these 1x2s, or I guess they're 2 1/2 in by 1 pieces, in there, it just makes it look finished and makes it look thicker and bigger and cleaner. It also strengthens the unit a little bit too. Anytime you add wood to a built-in cabinet such as this, you're going to strengthen the unit. Thing's built like a tank. I mean, it doesn't look like it, but everything's in studs, and whatever is not in studs, it's either glued or it's nailed to another board to make it just as strong as the other ones.
Step 9: The Divider Between the Washer and Dryer
The final trim piece I got to put in here is the divider between the washer and dryer. This is cosmetic really only, and actually I'm going to retract it a little bit. It actually is structural. It's going to help me keep that shelf up, and those trim boards in the front will have actually helped me keep the shelf from sagging. 3/4 in plywood will sag over anything over two foot really, so it's always nice to put trim boards in there to strengthen it up.
Step 10: The Stacked Cap Header
Here I am just putting on the top piece here. It's a 1x6, and then I also already installed the side piece, it's 1x6 also. It's going to give me a little bit of a cap. And then I took some of that 2 1/2 in that I ripped down and just put a little cap on top of the 1x6 to kind of give it like a stacked cap look. I don't really like angled crown too much. I really like the stack look. I think it's more modern, more craftsman, more farmhouse style.
And just like that I've got the skeleton built. You can see I pretty much hit my marks. I'm straight up the side. The unit's big but the room's big too. So the depth of the cabinet is 32, I think the width of it's about four foot six inches, all made by 3/4 in plywood, and then 1x material: 1x2, 1x4 and 1x6.
Step 11: Wainscoting Between the Built-In and the Door
Before I get on that back panel, I'm gonna simply put a little section of wainscoting between the built-in and the door. This is done the same way I did the wainscoting to the left. I basically write down my measurements, I make my cuts, I build the unit in the garage, and then I bring it in and plug it in. I use a little Liquid Nails behind it. This fits really firm here, so it doesn't take much to get it in, but it definitely finishes that little nook right there off really nice. I still gotta put a cap on the wainscoting. I just go measure it, and then I go out to the garage, cut it, and I install it. That finishes that whole small area off.
Step 12: Notch the Back for the 1/4 in Panel
Now the final piece I have to put in is that back panel. It's kind of a pain, to be honest with you. Now what I have to do here, I'm on the back side inside of the unit. I have to cut little notches out for this panel to slide in. I really didn't think about this too much. Probably should have. Would have been a lot, lot less work. I just would have went with a shorter 1x2 instead of a complete one, but then I wanted the unit to be firm too, so those 1x2s are doing more than just holding up shelves. No one's gonna see this behind here, so I don't have to be too picky about how it looks.
Here's that 1/4 in 4x8 sheet of plywood. What are they, like 29 or 28 dollars? I think it's birch. I think all my plywood is actually birch. It doesn't matter, as long as it's paint grade, what kind of wood you use on the panels. Everything gets primed and painted, so you can save money by going with a paint grade panel instead of a stain grade panel. These have to be smooth for the most part.
That table saw is the DeWalt table saw, battery only. Works great. I've never had a problem with it. And I tell you, those battery tools are incredible.
Step 13: Slide In the Back Panel and Finish the Base
Here I am putting the finishing touches on the built-in. Simply just slid that panel up in there. I'm going to use my nailer and nail a couple spots here and there. Really keeps the unit really firm. At this point it's a rock.
The only thing left I have to do is I've got some baseboard within the built-in, back here at the floor where the washer and dryer slide into. I don't really necessarily have to put it in there, but I had extra scraps, so I was like, oh, might as well. Might drive me nuts not knowing that it's not done. For the next guy, maybe. But for the most part, I had the wood, it didn't cost me anything. Just reused the old stuff and made a couple additional cuts to make it fit, and that pretty much finished up that area.
What's Next
Well, in the next video I'll finish up this framing, or I guess trimming, project, move on to the paint, and then some other goodies. The finishes will be coming soon.
And like always, I appreciate you spending time with the HomePro Hero.
Materials
- 3/4 in plywood, 8x4 sheets (two), cut at Home Depot to 32 in pieces plus the 16 in remainders (he says about $50 to $70 a sheet)
- 1/4 in plywood, 4x8 sheet, paint grade (birch, he thinks), for the shelf back (he says about $28 to $29)
- 1x2s (framing, cleats and backing)
- 1x4s, ripped to 2 1/2 in for face trim
- 1x6s (top header and side piece)
- Wood glue (wood to wood)
- Liquid Nails (wood to drywall)
- 1 1/2 in and 2 in nails
- Caulk
- Scrap baseboard for the base inside the built-in
- Wainscoting material for the section by the door (built the same way as the rest of the room)
Tools
- DeWalt 18 gauge nailer
- DeWalt battery table saw
- Level
- Home Depot panel saw (store cut, free)
Size and Cost
- Built-in: about 32 in deep, about 4 ft 6 in wide, 8 ft tall side panel.
- Cost: $275 for the built-in (three sheets of plywood). Final cost for the whole laundry room makeover, from the Part 7 reveal: $1,490.
The Rest of the Laundry Room Series
Ultimate Workshop Table Plans
The same mobile workbench from "Build This Workbench for UNDER $200," watched over a million times.
