All plans 25% off on the website. Use code WEB25 at checkout.
Backyard & Outdoor

I Built an Outdoor Sofa That Will Last Forever

A 6 ft outdoor couch that matches my chunky 2x6 chair, end tables and coffee table. The tools, the 5 degree angle brace, the hidden center leg, and what it cost: about $110 in lumber, $410 with the cushions.

One more outdoor furniture build. This time I'm going to show you how to build your own couch.

This build should be super easy. All I'm doing is copying the chair that I built: I Built a Chunky 2x6 Outdoor Chair. It's going to match my end tables and my coffee tables that I've recently built.

Plans for this exact sofa: Modern Wooden Sofa plans

Tools

Real simple. It's the same tools I used when I built the chair.

  • Miter saw. It's perfect for it, but a circular saw and a speed square would work fine.
  • Compact driver or a drill
  • Tape measure and a pencil
  • Caulk gun

Materials

  • 5 2x6 boards, 8 ft (preferably pressure treated for outdoor use)
  • 5 2x4 boards, 8 ft
  • 1 2x2 board, 8 ft (can be ripped out of an additional 2x4)
  • Standard Liquid Nails (adhesive)
  • GRK trim head screws, two and a half inch long, number eights
  • Sandpaper
  • Outdoor cushions and pillows

Step 1: Legs and sides

Let's cut four legs at 19 and three quarters. I like to double check these measurements, because I'm building two identical sides. So always double check it.

Step 2: The angle brace

The hardest part of this whole build is the angle piece. It's a 5 degree angle on both sides. It's 30 and a half inches from this point to the small point over there.

Step 3: Front seat board and the 6 ft pieces

I've got the front seat board on. It's 2x6 material. It matches the side stringers. Now I'm going to cut 2x4s to go in between. It's 6 foot, just like the front board.

The length of the couch: the middle pieces in the couch are 6 foot long, 72 inches. I already got the front 2x6 cut at 6 foot and the back 2x4, which is where the slats go, at 6 foot. So I just need three more 6 footers in 2x4 material.

I purposely ran these long. That way it'll stick in there while I get the screws in the side. I do want to use some Liquid Nails here.

Step 4: The hidden center leg

I am going to have to add a center support. 6 foot is too far for a 2x4 sitting flat like that. If it was on edge, it'd probably be fine. But I am going to run a hidden leg in the middle of that, just stepping up the middle.

If you've got three people on it, figure three people my size, you're talking a lot of weight. Three average size people, you're probably talking 600 pounds, maybe 500 pounds. So I want to make sure it's strong enough. I'm going to Liquid Nail that and screw that footboard in place, and center those other two in the middle.

Nothing worse than running short on wood. Let's cut these two pieces real quick.

Step 5: Finish it

I got the fake legs in there. They should be fine. I wish I could have tied them all together, but I'm not going to worry about it. I could if I wanted to, but I'm not going to mess with it.

This thing's built like a tank, just like the chair. Just got to sand it. Then get the couch inside the screened-in porch, get the tools put away, and wait for the cushions to come.

What it cost: $410

What did this DIY outdoor couch cost? I've got $300 in cushions and pillows. I've got about $110 in lumber and materials, for a total of $410. Not bad for an outdoor couch that will probably last forever.

Get the plans

The rest of the outdoor set

Modern Wooden Sofa Plans

A 6-foot outdoor sofa from "I Built an Outdoor Sofa That Will Last Forever."

See the plans